Wiki

start

phil (phil@undisclosed.example.com) — 2025-03-11T04:18:27+00:00

BOBST Tech - (973) 226-8000 * 924 * Saturn * DRO * Ward * Staley * J&L * Post * Expertcut * Conveyors * Towmotor * Unitizer * Baler room * Stitcher * Robot Backup * Trolley Car * Recovering from Power Outage * Unusual PMs * Hook up network to outside internet * Vocabulary * To be sorted

dro

phil (phil@undisclosed.example.com) — 2025-01-22T06:27:52+00:00

* AG Stacker pass: 6012 * load former user/pass * robot * Getting the encoder back in range * Changing the cam depth on supply pump * [LayBoy Belt Welding Procedure] * DRO Troubleshooting * DRO anilox roll change * [DRO feed roller cover change] * Cover location for Jackscrew to adjust parallel for feed roll

changing_the_cam_depth_on_supply_pump

phil (phil@undisclosed.example.com) — 2025-01-22T06:26:32+00:00

Changing the cam depth on supply pump Open the cover of the supply pump with a slotted screwdriver. Once the pump is exposed, turn down cam arms on pump and remove hose. Remove the cover of the can arms. There is a bolt holding the can arm assembly in-place. Remove this bolt and pull the can arm assembly out of the housing and flip over.

pxl_20250122_051032656.jpg - created

phil (phil@undisclosed.example.com) — 2025-01-22T05:58:23+00:00

pxl_20250122_051057161.mp.jpg - created

phil (phil@undisclosed.example.com) — 2025-01-22T05:57:15+00:00

924

phil (phil@undisclosed.example.com) — 2025-01-22T05:55:09+00:00

* 924 load former pass * 924 mosca password * 924 Encoders * Getting encoders back in range * Changing the cam depth on supply pump * light curtain plug wiring * [CEH COUNTER NOZZLE MOVEMENT SETTINGS] * [How to home the counter ejector blowers] * scrap conveyor motor starter * [Calibration of pre-scorer, scorer and slotter shafts] * robot * 924 troubleshooting

getting_encoders_back_in_range - created

phil (phil@undisclosed.example.com) — 2025-01-22T05:51:44+00:00

Getting the encoder back in range From the main operator HMI screen Tap the button on the bottom right of the screen to get to the main page On the bottom left hand of the main screen, tap the machine/toolbox button. On this new screen, tap the button with two gears below a gear on a threaded shaft

924_encoders

phil (phil@undisclosed.example.com) — 2025-01-22T05:50:37+00:00

Prescore encoder You need to navigate to the following screen to see the three decimal place readout of the prescorer encoder position. * The original encoder part number is SAM8346P00782 * The new encoder part number is SAM8346P00796 * dipswitch position

pxl_20241022_080241096.mp.jpg - created

phil (phil@undisclosed.example.com) — 2025-01-22T05:47:30+00:00

pxl_20241022_080236891.mp.jpg - created

phil (phil@undisclosed.example.com) — 2025-01-22T05:46:38+00:00

pxl_20241022_080231973.mp.jpg - created

phil (phil@undisclosed.example.com) — 2025-01-22T05:45:07+00:00

pxl_20241022_081325980.mp.jpg - created

phil (phil@undisclosed.example.com) — 2025-01-22T05:42:48+00:00

pxl_20241022_081330423.mp.jpg - created

phil (phil@undisclosed.example.com) — 2025-01-22T05:25:25+00:00

924_mosca_password - created

phil (phil@undisclosed.example.com) — 2024-11-01T05:38:33+00:00

* 111

load_former_user_pass - created

phil (phil@undisclosed.example.com) — 2024-10-18T06:18:15+00:00

* USER: amsi * PASS: 0356

machine_breaker_turns_off_not_due_to_high_current - created

phil (phil@undisclosed.example.com) — 2024-09-04T07:22:35+00:00

This voltage detection relay is located in the top-left of the feeder cabinet. It checks for phase imbalances that may cause damage to the frequency drives in the cabinet. How it works * The top, spin wheel (gray) needs to be set to ideal incoming voltage. In our case, 480V

crouzet_3-phase_voltage_detection_relay.jpg - created

phil (phil@undisclosed.example.com) — 2024-09-04T07:22:14+00:00

dro_troubleshooting

phil (phil@undisclosed.example.com) — 2024-09-04T07:21:09+00:00

* If you power cycle the machine because of weird errors, you must leave the machine turned off for a minimum of 10 minutes * AG stacker table extension will not retract/retracts very slowly * depth can't be greater than 19 * Secondary lift table will not lift up and down

cover_location_for_jackscrew_to_adjust_parallel_for_feed_roll - created

phil (phil@undisclosed.example.com) — 2024-07-25T06:35:23+00:00

Feed gate and side tamp will have to be moved to the center in order to expose the access panel to adjust jack screw.

imagepipe_14.jpg - created

phil (phil@undisclosed.example.com) — 2024-07-25T06:32:30+00:00